93LC46/P Microchip Technology IC EEPROM 1KBIT 1MHZ 8DIP
Integraallülitused (IC-d)
Tootja number:
93LC46/P
Tootja:
Tootekategooria:
Kirjeldus:
IC EEPROM 1KBIT 1MHZ 8DIP
RoHs olek:
Pliivaba / RoHS-iga ühilduv Andmetabelid:
93LC46/P Andmetabelid(PDF)
Juurdepääsu aeg :
-
Kella sagedus :
2MHz
Mälu liides :
SPI
Mälu suurus :
1Kb (128 x 8, 64 x 16)
Mälu tüüp :
Non-Volatile
Mälu vorming :
EEPROM
Osa olek :
Active
Paigaldustüüp :
Through Hole
Pakend/ümbris :
8-DIP (0.300", 7.62mm)
Pakendamine :
Tube
Pinge – toide :
2.5 V ~ 5.5 V
seeria :
-
Tarnija seadmepakett :
8-PDIP
Tehnoloogia :
EEPROM
Töötemperatuur :
0°C ~ 70°C (TA)
Tsükli aja kirjutamine – sõna, leht :
10ms
Laos
14,905
Ühiku hind:
Võtke meiega ühendust Pakkumine
93LC46/P Konkurentsivõimelised hinnad
ChipIcil on ainulaadne tarneallikas. Pakume oma klientidele 93LC46/P konkurentsivõimelise hinnaga. Saate nautida meie parimat teenust, ostes ChipIc 93LC46/P. Parima hinna saamiseks saidil 93LC46/P võtke meiega ühendust.
Hinnapakkumise saamiseks klõpsake
93LC46/P Iseärasused
93LC46/P is produced by Microchip Technology, belongs to Mälu.
93LC46/P Toote üksikasjad
:
93LC46/P – Mälu disainitud puhvervõimendid ja toodetud Microchip Technology.
93LC46/P, mida pakub Microchip Technology, saab osta CHIPMLCC-st.
Siit leiate erinevaid juhtivate tootjate elektroonilisi osi rahu.
CHIPMLCC 93LC46/P on range kvaliteedikontrolliga ja nõuetele vastav kõike nõuetele.
CHIPMLCC-s näidatud fondi staatus on ainult viitamiseks.
Kui te ei leia otsitavat osa, võtke meiega ühendust lisateavet, näiteks varude arvu andmetabelis 93LC46/P (PDF), hind 93LC46/P, Pinout 93LC46/P, manuaal 93LC46/P Ja 93LC46/P asenduslahendus.
93LC46/P, mida pakub Microchip Technology, saab osta CHIPMLCC-st.
Siit leiate erinevaid juhtivate tootjate elektroonilisi osi rahu.
CHIPMLCC 93LC46/P on range kvaliteedikontrolliga ja nõuetele vastav kõike nõuetele.
CHIPMLCC-s näidatud fondi staatus on ainult viitamiseks.
Kui te ei leia otsitavat osa, võtke meiega ühendust lisateavet, näiteks varude arvu andmetabelis 93LC46/P (PDF), hind 93LC46/P, Pinout 93LC46/P, manuaal 93LC46/P Ja 93LC46/P asenduslahendus.
93LC46/P FAQ
:
1. What is the function of the 93LC46/P semiconductor?
The 93LC46/P semiconductor is a 1K-bit low-voltage serial electrically erasable programmable read-only memory (EEPROM) device. It is commonly used for storing small amounts of non-volatile data in various electronic applications.
2. What are the key features of the 93LC46/P semiconductor?
The 93LC46/P semiconductor features a wide operating voltage range, low power consumption, and a simple two-wire serial interface. Additionally, it offers a high-speed clock frequency and a dedicated write protect pin for added security.
3. How is the 93LC46/P semiconductor typically connected in a circuit?
The 93LC46/P semiconductor is usually connected to a microcontroller or other digital device using a simple two-wire serial interface, consisting of a clock line and a data line. Additionally, it requires connections for power and ground, as well as a write protect pin if needed.
4. What are the typical applications of the 93LC46/P semiconductor?
The 93LC46/P semiconductor is commonly used in applications requiring small amounts of non-volatile memory, such as storing configuration data, calibration values, or user settings in various electronic devices including consumer electronics, automotive systems, and industrial equipment.
5. What are the main advantages of using the 93LC46/P semiconductor in a design?
The 93LC46/P semiconductor offers advantages such as low power consumption, small form factor, ease of integration with microcontrollers, and reliable non-volatile data storage. Its simple two-wire serial interface also simplifies the design of the overall system.
6. How does the 93LC46/P semiconductor handle data retention and endurance?
The 93LC46/P semiconductor is designed to retain data for an extended period without requiring power. Additionally, it has a high endurance for read and write cycles, making it suitable for frequent data updates in various applications.
7. What are the typical operating conditions for the 93LC46/P semiconductor?
The 93LC46/P semiconductor operates within a specified voltage range, typically from 2.5V to 5.5V, and at a recommended temperature range. It is important to adhere to these operating conditions to ensure proper functionality and reliability.
8. Can the 93LC46/P semiconductor be used in automotive applications?
Yes, the 93LC46/P semiconductor is suitable for use in automotive applications, provided that it meets the required specifications for temperature, voltage, and environmental conditions. Its small form factor and low power consumption make it well-suited for automotive electronics.
9. How can the 93LC46/P semiconductor be programmed and erased?
The 93LC46/P semiconductor can be programmed and erased using a simple two-wire serial interface, which allows for easy integration with microcontrollers or other digital devices. Specific commands and protocols are used to write, read, and erase data in the semiconductor.
10. Are there any special considerations for PCB layout when using the 93LC46/P semiconductor?
When designing the PCB layout for the 93LC46/P semiconductor, it is important to consider signal integrity, power supply decoupling, and proper routing of the serial interface lines to minimize noise and interference. Additionally, attention should be given to the placement of the semiconductor within the overall system for optimal performance.
I hope this information is helpful to you.
The 93LC46/P semiconductor is a 1K-bit low-voltage serial electrically erasable programmable read-only memory (EEPROM) device. It is commonly used for storing small amounts of non-volatile data in various electronic applications.
2. What are the key features of the 93LC46/P semiconductor?
The 93LC46/P semiconductor features a wide operating voltage range, low power consumption, and a simple two-wire serial interface. Additionally, it offers a high-speed clock frequency and a dedicated write protect pin for added security.
3. How is the 93LC46/P semiconductor typically connected in a circuit?
The 93LC46/P semiconductor is usually connected to a microcontroller or other digital device using a simple two-wire serial interface, consisting of a clock line and a data line. Additionally, it requires connections for power and ground, as well as a write protect pin if needed.
4. What are the typical applications of the 93LC46/P semiconductor?
The 93LC46/P semiconductor is commonly used in applications requiring small amounts of non-volatile memory, such as storing configuration data, calibration values, or user settings in various electronic devices including consumer electronics, automotive systems, and industrial equipment.
5. What are the main advantages of using the 93LC46/P semiconductor in a design?
The 93LC46/P semiconductor offers advantages such as low power consumption, small form factor, ease of integration with microcontrollers, and reliable non-volatile data storage. Its simple two-wire serial interface also simplifies the design of the overall system.
6. How does the 93LC46/P semiconductor handle data retention and endurance?
The 93LC46/P semiconductor is designed to retain data for an extended period without requiring power. Additionally, it has a high endurance for read and write cycles, making it suitable for frequent data updates in various applications.
7. What are the typical operating conditions for the 93LC46/P semiconductor?
The 93LC46/P semiconductor operates within a specified voltage range, typically from 2.5V to 5.5V, and at a recommended temperature range. It is important to adhere to these operating conditions to ensure proper functionality and reliability.
8. Can the 93LC46/P semiconductor be used in automotive applications?
Yes, the 93LC46/P semiconductor is suitable for use in automotive applications, provided that it meets the required specifications for temperature, voltage, and environmental conditions. Its small form factor and low power consumption make it well-suited for automotive electronics.
9. How can the 93LC46/P semiconductor be programmed and erased?
The 93LC46/P semiconductor can be programmed and erased using a simple two-wire serial interface, which allows for easy integration with microcontrollers or other digital devices. Specific commands and protocols are used to write, read, and erase data in the semiconductor.
10. Are there any special considerations for PCB layout when using the 93LC46/P semiconductor?
When designing the PCB layout for the 93LC46/P semiconductor, it is important to consider signal integrity, power supply decoupling, and proper routing of the serial interface lines to minimize noise and interference. Additionally, attention should be given to the placement of the semiconductor within the overall system for optimal performance.
I hope this information is helpful to you.
93LC46/P Seotud märksõnad
:
93LC46/P Hind
93LC46/P Maalimine
93LC46/P Tihvtide pinge
Pakkumised: Kiire hinnapakkumise kontroll
Minimaalne tellimus: 1
Sisaldab "93LC" seeria tooteid
